Odborník, který napsal 20 odpovědí o více než 400 znacích.
- Odborník 99 Odpovědi
- Publikováno 26. dubna 2019
Expert, který dosáhl úrovně 2 získáním 100 bodů
Expert, který získal 5 úspěchů.
Web navštěvoval 3 po sobě jdoucí dny.
Odborník, který napsal 20 odpovědí o více než 400 znacích.
Připojeno: 22. dubna 2011
What model car? Most that I know of are located in the glove box. That allows you to LOCK the glove box with the key after setting valet button. IF in glovebox it may be in console where a lock is installed.
Nemůžete posílat komentáře, které obsahují e-mailovou adresu.
Přidejte svou odpověď
Tipy na skvělou odpověď:
- – Odpovědět na otázku.
- — Pokud potřebujete vysvětlení, zeptejte se ho v poli pro komentáře výše.
- — Lepší odpovědi používají správný pravopis a gramatiku.
- — Poskytněte podrobnosti, podporu s referencemi nebo osobními zkušenostmi.
Řekněte nám ještě něco! Vaše odpověď musí obsahovat více podrobností, aby pomohla lidem. Nemůžete zveřejňovat odpovědi, které obsahují e-mailovou adresu. Prosím zadejte platnou emailovou adresu. Zadaná e-mailová adresa je již přidružena k účtu. Přihlaste se pro příspěvek Používejte pouze anglické znaky.
Tip: Maximální bodová odměna za zodpovězení otázky je 15.
Nahrajte obrázek ze svého počítače
Nakreslete rámeček nad problémem!!
Zavřít Uložit změny
Přílohy: Přidané položky
Nahrávání: %
můj-video-soubor.mp4
Kompletní. Kliknutím na „Přidat“ vložíte své video. Přidat
Načítání.
Zahrnout obrázek. Stojí to za tisíc slov.
Související dotazy:
Servisní režim
The valet button location is decided by the installer and is usually hidden. Find the main control unit and follow the 2 wires to the valet switch.
Feb 10, 2014 • 350 HV ESP Security System 350HV ESP
Car starter in valet mode
- 1 Insert the key into the ignition.
- 2 Turn the ignition switch to «ON.» Do not start the engine.
- 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
- 4 Release the valet/override button after the security indicator light turns off.
- 5 Turn the ignition switch off.
07. prosince 2013 • Dodge Cars & Trucks
Location of valet/override button on dodge durango 19999
The valet/override button is located right under the steering column on your 1999 Dodge Durango. To reset the alarm, press and hold the button within five seconds of cranking up the engine — release it when the security lights stop blinking.
Aug 27, 2012 • Dodge Durango Cars & Trucks
Valet switch location
The valet switch is usually located around the drivers side. Each installation is different, as are most alarms. The valet switch could be part of the flashing LED or, it could be incorporated into the on glass antenna. If not, it should be located below the driver side dash. If you can see the alarm, locate the blue two pin plug and trace the wire to the push button valet. If the unit is manufactured by Directed (Viper, Python, Avital, Clifford, Valet, Automate, Hornet, etc.) turn ignition on then off, press and release valet within 10 seconds, LED will illuminate solid to show system is in valet. If the unit is manufactured by Audiovox (Prestige, Pursuit, Code (new)) turn ignition on, press and hold valet switch for approx. five seconds, release, LED will illuminated solid to show system is in valet.
If you are attemting to manually override the system, turn ignition on, press and release valet switch to disarm.
Aug 21, 2012 • 1995-1997 Chevy Tahoe Ignition Starter.
Charged battery on 1997 Toyota Camry now immobilizer will not lock doors and car will not start
Here is the reset procedure:
1. Have the Valet Button in the OUT position. ( It is located on the dash panel left of the steering column)
2. Connect the battery — the alarm will sound.
3. Put the key in the ignition and turn to the ON position,
4. Push the Valet Button to the IN position.
The alarm will be reset, and the Valet Button will glow red.
Move the Valet Button to the OUT position again.
Repeat steps 3 & 4 and the Valet Button will become unlighted.
The car will start and everything will be fine.
Apr 20, 2012 • Toyota Camry Cars & Trucks
Where is the valet switch on a 2004 chevy malibu LS?
There should be a key specifically for a valet.
1) Open one of your vehicle’s doors and turn the ignition, using the car key, to the «Run» position. Check to see that the dome light comes on. Make sure that you have the dome light set to the position where it powers the light when the door is opened, as there are usually three settings: one for «On,» one for «Off» and one for when a door is opened.
2) Press the valet remote push-button to access the channel that you want to program: once for «Arm/disarm,» twice for «Trunk Release» and three times for «Remote Start.» The valet push-button is usually located under the driver’s side panel, and it must be pressed within 15 seconds of opening the door. The push-button may also be installed underneath the kick panel.
3) Press the valet push button once again and wait to hear a chirping or a honking sound. If you do not hear either of these sounds, your vehicle might have a jumper installed that has turned the valet programming feature off. Refer to your vehicle’s instructional manual to learn how to set the valet programming feature to the «On» position. Keep holding the valet button pressed as you continue onto the next step.
4) Push the button on the remote that you wish to assign to a particular valet channel. Press the button on the hand-held valet remote that you wish to assign to a particular valet channel. If you wish to program multiple remotes, repeat this step for each of them. If you program four or more remotes, the old programming will be erased.
5) Let go of the valet push-button and exit your vehicle. Your handheld remote is now ready to use.
Tipy a varování — Some valet remote channels require different programming individually, so refer to the owner’s manual or to the link provided in the «Resources» section of this article, for specific instructions.
— Valet remote programming methods may vary, depending on the vehicle’s make and model.
