Many Honda Accord owners rely on their car’s radio to keep them entertained and informed while on the go. But what do you do when the dreaded “error E” pops up on the screen, preventing you from listening to your favorite stations?
Don’t worry – we’re here to help you with the reset. In this blog post, we will walk you through the process of resetting the Honda Accord radio code error E.
When the radio displays error code E, disconnect the black negative battery cable for one to three minutes to reset it. Look for the word “code” after turning the radio back on and enter the 5-digit radio code, and the radio should turn back on.
What Is A Radio Error E?
A radio error E is a general protection fault code that indicates an issue with the car’s audio system. This can be caused by a number of things, including a loose connection, an accessory that has been added to the system, or a problem with the software.
How Can I Tell If My Car Radio Han An Error E?
Don’t worry about trying to figure out if you’re suffering from this error, it will be quite obvious. The radio in your Honda will display the error E code if it’s locked. You’ll need your five-digit code to unlock it. If you attempt to enter the wrong code too many times, you’ll get a big “ERROR” message on the radio screen.
If you try to enter the code too many times and get locked out, you can start over. Follow the directions in the next section if you’ve exceeded the number of attempts to enter the correct code.
How To Reset The Honda Radio Code Error E
When your Honda radio asks you to input the code, it either means that the battery has died or that you just newly replaced it. You’ll need a radio code that may be accessed through the Honda databases to reset it.
If this is your first time, don’t worry – the process is simple and only takes a few minutes if you follow the steps below:
1. Get The Serial Number
First, locate the serial number of your radio. This can be found on a sticker that is affixed to the top or side of the radio unit. Once you have located the serial number, call Honda customer service at 800-999-1009 and request the radio code for your vehicle.
Be sure to have the following information ready when you call:
- The serial number of your radio
- Your vehicle identification number (VIN)
- The phone number where you can be reached
A customer service representative will ask you for this information to verify your identity and pull up the radio code for your vehicle.
2. Put the Car On Auxilliary Mode
Turn on your car and press the “AUX” button on your radio. This will put the radio into the auxiliary mode, allowing you to input the code.
In case you do not see an AUX button, look for a button that says “MODE” or “SOURCE.” Pressing this button will cycle through the different modes until you reach the auxiliary.
You can also put the car into accessory mode by turning the key to the “ACC” position without starting the engine. This will power on the radio without starting the car, allowing you to input the code.
3. Turn The Radio Off
Once you have the radio in auxiliary mode, press the “PWR” or “POWER” button to turn the radio off. This is typically located on the face of the radio.
4. Turn The Radio On
While holding the numbers one and six, with your free hand, press the power-on button. Your car radio’s serial number will appear on the display.
5. Input the five-digit code using the preset buttons on your radio.
The first digit of the code corresponds to the first preset button, and so on. For example, if your code is 43679, you would press “43.”
Release the one and six buttons after you have inputted all five digits of the code. The radio should turn back on, and you can begin using it normally.
Are there other methods for resetting the error E code?
Yes, there are a few other ways that you can reset the code on your Honda radio if you’re experiencing the error E code. These methods may vary depending on the model of your car, so it is best to consult your owner’s manual or contact a Honda dealer for more specific instructions.
One method is to disconnect the battery and then reconnect it after a few minutes. This will reset the radio and allow you to input the code.
Another method is to press and hold the power button on the radio for at least five seconds. This will also reset the radio and allow you to input the code.
Do I have to reset the radio every time I disconnect the battery?
No, you should not have to reset the radio every time you disconnect the battery. The code is typically only required when you replace the battery or if the power to the radio is interrupted for some reason.
When you find that you have to reset the code frequently, there may be an issue with the battery or electrical system in your vehicle. It is best to consult a Honda dealer or qualified mechanic to diagnose and resolve the problem.
Are There Other Error Codes for Honda Radio?
Yes, there are other error codes that can display on your Honda radio. These codes indicate different issues and will require different solutions. Some of the most common error codes are:
Error Code B: This code indicates that the battery in your vehicle is low and needs to be charged.
Error Code P: This code indicates that there is an issue with the audio system in your vehicle.
Error Code U: This code indicates that there is an issue with the USB port in your vehicle.
In case you see any of these error codes, or any other that we have not highlighted, it is best to consult your owner’s manual or contact a Honda dealer for further assistance.
FAQs About Code Error E
Does Code Error E Occur on Civics, Accords, CRVs, Odysseys, Pilots, and on specific years?
The code error E can indeed happen in a number of different models. Below is the list of commonly affected models and years that our users have reported:
- Honda Accord 1998, 1999, 2000, 2001, 2002, 2004, 2005, 2006, 2007, 2009
- Honda Civic 2000, 2001, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011
- Honda CRV 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2016
- Honda Odyssey 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
- Honda Pilot 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
If you experience code error E on any of the above models, the process for fixing the error should be the same as I have outlined above. If you still have difficulty, contact your nearest Honda dealer for assistance with getting past the code error E.
How do I know if my car radio has the code error E?
If you see the error E code on your Honda radio, it means that the radio is locked and needs a five-digit code to be entered in order to unlock it.
Where can I find the serial number for my car radio?
The serial number for your car radio is typically located on a sticker at the top or side of the radio. If you cannot locate the serial number you can contact Honda customer service.
I cannot find my car owner’s manual. Where can I get more information about resetting the code on my Honda radio?
If you cannot find your car owner’s manual, contact a Honda dealer or qualified mechanic for more information. You can also find helpful information on the Honda website.
Do I need to enter the code every time I turn on my radio?
No, you should not need to enter the code every time you turn on your radio. The code is typically only required when you replace the battery or if the power to the radio is interrupted for some reason.
What do I do if I see other error codes on my Honda radio?
There are other error codes that can display on your Honda radio. These codes indicate different issues and will require different solutions.
Final Words about Code error E
Encountering the error E code can be rather frustrating, especially if you don’t have your 5-digit code, but it doesn’t have to be. Take a breath, read through our instructions and you should be back in action listening to your favorite tunes in no time!
We hope that this article was helpful in explaining how to reset the Honda Accord radio code error E. If you have any further questions, please feel free to reach out to us. We would be more than happy to help.
Také by vás mohly zajímat tyto články:
If you enter the wrong radio code too many times, your Honda radio will display CODE ERROR E. A Honda radio that displays the error E code means the radio is locked and needs a five-digit code to be unlocked
Radios in Hondas work as usual under regular use, but sometimes the radio code needs to be reset. Depending on the model, you may be able to reset the radio codes yourself or bring it to a dealer.
If your Honda radio displays error E, then you must reset it. Factory radios that require a code to operate have a battery-operated anti-theft feature.
Reinstall the radio fuse after disconnecting the battery or pulling it. The radio will no longer display the code error. The owners’ manual packet should have a small card containing a five-digit identification number.
To enter this code, the battery must be disconnected. Before it is locked, you will have five tries to enter the code.
What Is A Radio Error E?
An E error code on a radio indicates a problem with a car’s audio system. Several reasons exist, including a loose connection, a new accessory, or software problems.
How Do I Know If My Car Radio Has An Error E Code?
Your Honda radio will display the error E code if it is locked and needs a five-digit code to be unlocked. You will see “ERROR” on the radio screen if you enter the wrong code too many times.
For maybe 15 seconds, hold the positive and negative cable ends (not connected to the battery) together if it says “ERROR.” Reset the system after that. You can then start over again with the “CODE” command.
Error E On A Honda Radio: How Do You Reset It?
To reset the radio, disconnect the battery first. The radio will say “Enter Code” or “Code” when you turn it on after reconnecting the battery.
Your local Honda dealer can provide you with the code (or perhaps you already have it). You will receive this error if you have entered the radio code incorrectly more than three times.
For a quick reset, disconnect the black negative battery cable from the radio for one to three minutes when the radio displays error code E.
The radio should turn on after you enter the 5-digit radio code after the radio has returned to its original state. You can easily complete this process if this is your first time. Follow these steps to get started:
1. Obtain The Serial Number
Start by finding your radio’s serial number. The radio unit has a sticker attached to the top or side that contains this information.
You can request the radio code for your vehicle by calling Honda customer service once you’ve located the serial number. When you call, please have the following information ready:
- Your radio’s serial number
- The VIN of your vehicle
- Vaše kontaktní informace
A customer service representative will ask you for this information to verify your identity and retrieve your vehicle’s radio code.
2. Put The Car In Auxiliary Mode
Press the “AUX” button on your radio when your car is turned on. You can then enter the code by putting the radio in auxiliary mode.
Alternatively, look for a button that says “MODE” or “SOURCE” if you don’t see an AUX button. Auxiliary can be selected by pressing this button.
Turning the key to “ACC” without starting the engine can also put the car in accessory mode. Doing this allows you to input the code while the radio is on without starting the car.
3. Turn Off The Radio
The radio can be turned off by pressing the “PWR” or “POWER” button once it’s in auxiliary mode. On most radios, this can be found on the face.
4. You Need To Turn On The Radio
Press the power button while holding numbers one and six. On the display of your car radio, you will see the serial number.
5. Use Your Radio’s Preset Buttons To Enter The Five-Digit Code
According to the code, the first digit corresponds to the first preset button. So, as an example, you would press “43” if your code was 43679.
Once you have entered all five digits of the code, release buttons one and six, you can now use the radio as usual once it turns on again.
What Is The Process For Resetting A Honda Radio After A Battery Change?
The radio may be affected when you change the battery in your car. After changing the battery on your Honda, you can easily reset the radio by following these steps:
- Before starting the engine, turn the key to the ON position.
- Next, turn on the radio by pressing the volume control knob.
- Turn the radio off again after 10 seconds.
- Finally, turn on the radio display by pressing and holding the power button.
- Input your radio code if the Enter PIN message appears on your radio, which can be found in your owner’s manual.
- The radio preset buttons can be used to input the code. Your radio should be reset after entering the code.
You can reset your Honda radio by following these steps. The owner’s manual provides further instructions on how to fix the radio, or you can bring it to a Honda dealer for a quick repair.
Is There Any Other Error Code For Honda Radios?
Your Honda radio can display other error codes as well. However, there is a difference between these codes and the solutions they indicate. There are several error codes that are commonly encountered, including:
Error Code B: Your battery needs to be charged if this code appears.
Error Code P: Your vehicle’s audio system is malfunctioning.
Error Code U: Your vehicle’s USB port is malfunctioning.
We recommend consulting your owner’s manual or contacting a Honda dealer if you notice any error codes or others not highlighted here.
Should I Reset My Radio Every Time I Disconnect The Battery?
There should be no need to reset the radio each time the battery is disconnected. However, the code is needed if the power to the radio is interrupted for some reason, or if you replace the battery.
Your vehicle’s battery or electrical system may malfunction if you have to reset the code frequently. If you have a problem with your Honda, you should consult a Honda dealer or a qualified mechanic.
Can The Error E Code Be Reset In Any Other Way?
The Honda radio can be reset in a few different ways. Your owner’s manual or Honda dealer can provide you with more specific directions depending on your car’s model.
A simple method involves disconnecting and reconnecting the battery after a few minutes. You can input the code after the radio has been reset.
Another method is pressing and holding the radio’s power button for at least five seconds. By doing this, you will also be able to input the code and reset the radio.
How Do I Fix Other Honda Radio Error Codes?
In addition to these error codes, your Honda radio may display other messages. Depending on the code, different solutions will be required.
Závěrečná slova
When you recently replaced your car battery, you noticed that your Honda radio was locked out. If this is the case, you cannot listen to your favorite music while driving.
There’s a good chance that you’re locked out because a factory-enabled anti-theft system has been activated. Despite its purpose of preventing car radio theft, the lock can also prevent the owner from accessing the audio system.
Fortunately, this is a common issue that can be easily resolved. As long as you follow the above steps, you can enjoy your music or listen to your favorite podcast while driving.
O Gary Piotrowském
Jsem strojní inženýr a automobilový inženýr s více než 12 lety zkušeností v automobilovém průmyslu. Šest let pracuji pro in-tech Automotive Engineering, LLC.
Jsem zodpovědný za navrhování a vývoj nových produktů, procesů, materiálů a technologií, které lze použít ke zlepšení bezpečnosti a výkonu vozidel. Pracuji také na zlepšování efektivity výrobních procesů a snižování nákladů.
Rád čtu o automobilech, motocyklech a dalších dopravních systémech, abych prozkoumal nové nápady, které lze použít v mé práci.
LinkedIn
