*NYNÍ REZERVOVÁNO NA ROK 2024* Transitmania 15 @ Santa Pod 19. až 21. července 2024 *VŠECHNY PODROBNOSTI ZDE*
Battery change — Battery Monitor System re- programme .
Pomocí této sekce můžete zveřejňovat všechna konkrétní témata a dotazy týkající se Transit Connect
4 příspěvků • Stránka 1 of 1
Battery change — Battery Monitor System re- programme .
by Stříbrná liška » Ne 16. 2020. 12 13:XNUMX
I have a question regarding changing my old 5 year battery on a Ford Transit, short wheel base, 2015 UK model, 1.6L Diesel, for a new Ford OEM battery.
Looks a nightmare to replace, its on the right hand side of the engine bay, tucked well under the windscreen wiper sill. Looks like the whole air filter body and other stuff will have to be removed to get to it
I have heard stories regarding the following below
Once the battery is fitted, does the Battery Monitor System (BMS), has to be calibrated when the battery is replace.
«The BMS is used to calculate the state of charge of the replacement battery, it monitors the current, temperature and voltage of the battery. If the BMS is not told of the new (replacement) battery information, ie, amperage, voltage, and new serial number of the battery, it can cause the alternator to overcharge the battery, it could boil the battery, cause damage to the vehicles electrical system and basically fry the electrics in the vehicle by over charging or even undercharging».
If the vehicle battery is replaced, it is very important to perform the battery monitoring system reset using the scan tool.
If the battery monitoring system reset is not carried out, it holds the old battery parameters and time in service counter in memory. Additionally, it tells the system the battery is in an aged state and the may limit the Electrical Energy Management system functions.
In that context «scan tool» refers to the genuine Ford diagnostics device used by dealers. The BMS data is held in non-volatile memory (it is retained even when the battery is disconnected) and cannot be reset by any means other than use of an appropriate tool plugged into the diagnostics port on the car to send the correct ‘BMS reset’ command-code to the Body Control Module (BCM).
Does the Transit connect even have a BMS?
Can I just swap over the battery and that’s it. People say the battery can be boiled, the windows might stay down if you open them, the radio might not work, and even the vehicle might not start again.
I know BMW’s have to have the new battery info programmed into the vehicle and Audis also, what about the Ford Transits? Ford said they don’t know about this issue, but a tyre and exhaust place in the UK, said it needs to be done with a reset tool?
If it has to be done, where can I purchase a battery reset tool to upload the new battery info into the vehicles memory ?
Jakákoli pomoc by byla velmi ceněna.
Silverfox Newbie Příspěvky: 2 Založen: So 15. srpna 2020, 11:33
Re: Battery change — Battery Monitor System re- programme ??
by swishvan » St 02. září 2020 10:15
I had a new battery fitted at a ford dealer on a 2014 and the technician replaced in in about 5 mins without setting any thing had to switch hill start assist back on using the dash buttons and that was it
swishvan Transit Aficionado
Příspěvky: 105 Založen: So 01. března 2008 5:39
Re: Battery change — Battery Monitor System re- programme ??
by Stříbrná liška » So 26. září 2020 12:44
Many thanks for your reply
Silverfox Newbie Příspěvky: 2 Založen: So 15. srpna 2020, 11:33
Re: Battery change — Battery Monitor System re- programme ??
by Altransit » So 26. září 2020 4:13
If it’s similar to the Mk3 Focus, you have to undo the front end of the battery tray, hinge it forward, and lift the front of the battery up, as you pull it forward from under the scuttle.
In the older Focus, you had to undo the scuttle panel to give yourself more room, it could be like this on your Connect.
I’ve changed the battery a couple of times in the Focus, and never reset the BMS, but if it becomes necessary, (for whatever reason) you only need the ELM327 lead, and a laptop with Forscan, to reset the BMS.
1994 Mk4 SWB 115 Minibus 70ps Di (R.I.P.)
1997 Mk5 SWB 115 Minibus 70ps Di (Gone, but not forgotten!)
2004 Mk6 SWB T280 Medium Roof 85PS 2.0 TDDi — Vantunered (Also gone)
2008 Mk7 SWB T280 Medium Roof 85PS 2.2 TDCi — Also Vantunered
Altransit Site Moderator Příspěvky: 39986 Založen: Út 17. října 2006 12:23 pronájem: Bicester, Oxfordshire, UK
Your Ford Transit radio isn’t working properly. Now, you’re thinking about resetting the system to try and restore its normal functions, but how do you do this? We researched this concern for your convenience and here’s the answer we found.
Take note that resetting a Ford Transit radio generally depends on the specific vehicle model. Here’s an example of one way to reset the van’s radio:
- Press the “SYNC” button, which should make the main display appear.
- Navigate through the menu until you can find the advanced menu.
- Find the “Master Reset” item in the advanced menu
- Press the “OK” button on the dashboard to confirm the selection.
- Press the “OK” button again if the system asks if you’re sure about the decision.
- Wait for the radio to reboot.
It’s also important to mention that resetting a Ford Transit’s radio may not be successful after engaging its Master Reset function. Instead, you may need to replace the entire module for it to work properly. So continue reading as we talk about this alternate solution to returning the van’s radio’s normal functions.
How Do You Replace The Radio Of A Ford Transit?
Bear in mind that not every aftermarket radio on the market is compatible with a Ford Transit. Ask your radio dealer if the unit you’re purchasing can fit your van before finalizing the purchasing decision.
Once you have a compatible replacement radio for your Ford van, follow these steps to continue the operation:
Co budete potřebovat
- Šroubovák
- Odstraňovač panelu
- Replacement Ford Transit radio kit
Podrobný průvodce
Krok #1: Zajistěte vozidlo
Start by disengaging the van’s engine and engaging its hand, parking, or emergency brake. At this point, you may also want to open the hood and disconnect the negative battery cable from its terminal.
Step #2: Remove The Radio Display
Pull out the top cover from the radio assembly with your hands, which should also expose two screws. Loosen and remove those screws afterward.
Lift the radio’s display upward carefully. Look at its bottom and you should see a small tab. Lift that tab to disconnect the cable attached to the display. With the cable detached, you can now set the radio’s display aside.
Step #3: Remove And Replace The Front Panel
Loose and remove the screws securing the radio’s front panel. Then, use the panel remover to pry the cover on top of the front panel. Loosen and remove any additional screws on the radio assembly afterward.
Pull out the radio’s front panel carefully. Disconnect the wires attached to the panel. Replace the front panel with the unit in your Ford Transit radio replacement kit.
Note: You may not need to replace the front panel if you’re only going to swap out the old ACM module with a new unit.
Step #4: Replace The Main Radio
Loosen and remove the screws on the main ACM radio module. Disconnect the wires attached to that assembly afterward.
Next, use a Philips screwdriver to remove the mounting bracket on the old ACM radio module. Once removed, place and secure the bracket to the same location in the new radio module.
Route the wires included in your radio installation kit. Connect those wires to the main new ACM radio after you route the connections.
Step #5: Return The Parts And Test
Return the parts you removed from the previous steps to their original locations. You can also swap out the old front panel with a new unit if your radio installation kit has it.
After reassembling the entire radio assembly, turn on the Ford Transit’s engine. Then, turn on the radio to test out its functions. At this point, you should also inspect for any persisting issues (or lack thereof) in the van’s radio.
You can also check out this video if you need a visual guide for the steps mentioned above:
Also, watch the video below if you need additional help with the radio removal process:
How Do I Reset My Ford Transit Radio From My Phone?
If you don’t want to replace your Ford Transit’s radio yet, you may try resetting the system through your phone. Follow these general steps on how to connect your smartphone to the van’s radio so you can reset the system from that device:
Podrobný průvodce
- Turn on the Ford’s engine and ensure that the radio and/or infotainment system is active.
- Turn on the Bluetooth on your smartphone and ensure the device is discoverable.
- On the infotainment system, search for the “Add Phone” menu item.
- Pair the phone with the radio by confirming the pairing request.
- With the smartphone paired, tap the gear icon on the lower right of the Ford SYNC Applink application’s home screen on your phone.
- Locate the “Master Reset” menu item and tap on it.
- Confirm the action and wait for the system to reboot.
Warning: Activating the Master Reset function on your Ford Transit radio will erase all of its stored data regardless of the method used to initiate the feature. You can save your data by removing the SD card or backing up the files in the system before you proceed with resetting the radio.
How Do I Find My Ford Transit Radio Code?
If you need the security code for your Ford Transit radio, you may find it in the vehicle’s owner’s manual. Otherwise, the alphanumeric combination might be in other documents included in the point of sale. If you still can’t find the code, contact the vehicle manufacturer for assistance.
What Is The Best Radio For A Ford Transit?
Finding the best radio for your Ford Transit typically means understanding your automotive audio preferences. Also, the selection process often needs you to check the compatibility of your preferred replacement radio assembly.
Nonetheless, here are some models you can check out that might also pique your interest:
1. Rimoody Android Car Stereo
It’s important to note that this radio and infotainment system is only compatible with Ford Transit made within the 2013 to 2018 period. It’s also more expensive than other similar models on the market. Still, you may justify the bump in price by looking at its features.
For instance, it’s compatible with Android Auto and Apple Carplay. Yes, you can now see many infotainment systems that can use smartphone syncing features. But this particular stereo takes it up a notch by allowing users to control their phone’s functions wirelessly through the infotainment display.
You can also download offline maps into the built-in GPS navigation system. This feature can work well for phones that aren’t compatible with this unit’s Android Auto and Apple Carplay navigation features. Plus, the kit includes backup and rear-view cameras for added security.
2. Rimoody 7-Inch Touchscreen Car Radio
Don’t confuse this particular model with the product mentioned previously. This 7-inch touchscreen radio and infotainment system is the smaller sibling to the previous item. It also has a less expensive price tag compared to its 9-inch relative.
Despite its lower costs, this Rimoody car radio still has wireless Android Auto and Apple Carplay capabilities. Users can also download offline maps into its built-in navigation system if needed.
However, this kit doesn’t include backup and rearview cameras. Nonetheless, users can take advantage of other features, such as a subwoofer and microphone output, a built-in equalizer, and digital AM and FM radio support.
3. Alpine iLX-W650
This particular Ford Transit radio sits in the high-end sector, thanks in part to its expensive price tag. The Alpine iLX-W650 promotes a plethora of different features to suit the audio needs of different users.
Tinker with this radio system’s features, and you’ll find elements like Pandora and Spotify compatibility, USB ports, and Android Auto and Apple Carplay compatibility. But perhaps one of the features that may pay entice audiophiles into purchasing this unit is its compatibility with FLAC files.
FLAC stands for Free Lossless Audio Codec, and it’s a file format that typically has better-sounding properties than the standard MP3 audio file.
Závěrečné myšlenky
Resetting your Ford Transit radio may start with tinkering around with its built-in buttons and features. If accessing and engaging the Master Reset function doesn’t work, you may need to replace the entire assembly with a new and compatible model.
If you’re looking for answers to other vehicle radio concerns, check out these other posts:
Související příspěvky:
- How To Set The Clock On A Ford Transit Connect
- Jak resetovat rádio ve vašem Hyundai Accent
- Kde se nachází baterie Ford Transit?
- How To Reset Ford Sync?
