ford3

It doesn’t really matter whether we are talking about PIN numbers, phone numbers or your phone’s access code, nearly all of us have experienced the pain of not being able to remember an important number at some point or another. The Ford keyless entry code is no different, and that’s why I created this guide to reset it.

How to Reset Ford Keyless Entry without Factory Code

Well, unless you are in an extreme emergency, you will need some time to reset your code and start the car. In this guide, I will answer the question, what is the keyless system used in Ford and how does it operate? And will also answer the question, how do I reset a Ford Keyless Entry without the Factory Code.

Before I give you that amazing three step hack to find the factory 5-digit code in any Ford that has this mechanism, let’s look at what the system does.

SECURICODE TM KEYLESS ENTRY KEYPAD

Depending on the vehicle make and model, the keypad is usually found near the driver’s window. Pressing on the keypad will make it light up which makes pressing the right combination code easy and fast. Remember, don’t press the code in too fast, or the system might not accept the code. If this happens, just re-enter the code again.

The Ford Keyless Entry mechanism provides the following functions:

  1. Zamkněte nebo odemkněte dveře
  2. Recalls saved seat and mirror positions
  3. Arms and disarms the anti-theft alarm
  4. Otevře kufr
  5. Programs and erases personal entry codes

The system comes with a factory set 5-digit code which is found in the original wallet card that was placed in the glove box and is also available from an authorized dealer. However, if you do not have a new car, these might not exist, and in this case, apart from memory and writing the code down, you have another option, and that is to program up to five x 5-digit personal entry codes.

ČTĚTE VÍCE
Jak spustím dálkové ovládání okna Ford?

Now, let’s take a look at the functions mentioned above.

Odemykání a zamykání dveří

odblokování: Enter the 5-digit code, or your personal code Make sure you press each number within five seconds then press 3•4 within five seconds of each other. When this occurs, the interior lamps will illuminate, and all the car doors will unlock.

Zamykání: Make sure the driver’s door is closed, then press and hold 7•8 and 9•0 simultaneously. You don’t need to enter the 5-digit code for this operation.

Otevření kufru: Enter the 5-digit code or your personal code Make sure you press each number within five seconds then press 5•6 within five seconds of each other.

Ford Keyless Entry

Program a personal Code

  1. Enter the factory-set code and then press 1•2 within five seconds.
  2. Now enter your personal 5-digit code. Remember, you must press each number within five seconds of each other. Then press 1•2 to save your personal first personal code.
  3. To confirm you were successful the doors will lock and unlock.
  4. You can add up to 5 different codes using this method, and the only difference between each code is the number you press for confirming them:
    1. For code 2 press 3•4
    2. For code 3 Press 5•6
    3. For code 4 press 7•8
    4. For code 5 press 9•0

    After setting your five codes, the factory code will still operate, so you now have 6 options to forget.

    Recall a memory position

    Entering a personal code will return the saved position for every driver, so if you created a code for a specific position you need to enter that code into the mechanism to return the position.

    Vymazání osobního kódu

    You can erase personal codes by simply entering the factory-set 5-digit code and then press and release 1•2 within five seconds, then press and hold 1•2 for two seconds, but make sure you do this within five seconds from pressing 1•2 the first time. Now all the personal codes are erased.

    Anti-Scan Function

    There is an anti-scan system in place when 35 sequential numbers are entered incorrectly; the mechanism will lock down for one minute. You can reset the system by performing one of the following procedures:

    1. Wait the one minute.
    2. Press unlock on the remote control
    3. Zapněte zapalování
    4. Use intelligent access to unlock the car
    5. Enter the factory set code

    Finding the Factory 5-Digit Code

    Using the Integrated Keyhead Transmitters

    You can display the factory-set code in the information display, but to do this, you will need two programmed passive anti-theft keys. Make sure you have a pen and paper or have a smartphone cam ready in photo mode.

    1. Insert one key into the ignition and switch on for a few seconds.
    2. Then remove the key and repeat with the second key.
    3. Sometimes, before the factory-set code will display other warning messages will appear, and then for a few seconds the factory code.
    4. Either write down the code or take a quick photo of it.

    Using Intelligent Access Keys

    To display the factory-set code in the information display, you will need both programmed intelligent access keys.

    1. Slide the first programmed key in the backup slot inside the center console.
    2. Make sure the key ring is at the tip, and the buttons are facing the rear.
    3. Now press the START/STOP button once, wait a few seconds and then press it again and then remove the key.
    4. Now slide out the key and slide in the second key and press the START/STOP button.
    5. Sometimes, before the factory-set code will display other warning messages will appear, and then for a few seconds the factory code.
    6. Either write down the code or take a quick photo of it.

    Can I reset the Ford Keyless Entry without the Factory Code?

    Odpověď je: Ne.

    You need the code; the factory code is the only way to program and use the system. So, if you cannot find it, cannot access it, then you need to hack it, and here is the simplest, and easiest method to hack a 5-Digit factory code form all and every Ford vehicle that uses the keyless system.

    Hack: Finding the 5-Digit Code

    Yes, it happens, you don’t have any way to find the 5-digit factory code. Either you are just unlucky, or you are a car thief, and you want to start the car without the code. So, here goes.

    1. Remote Anti-theft Personality (RAP) Module

    Since you don’t have the code, you have to access the RAP which is found in a removable panel at the back of the vehicle.

    You will need a flashlight. Locate the panel, to remove it turn the two-thumb counterclockwise.

    Shine the flashlight on the module and look for a label, it has the factory code printed on it.

    Závěry

    Sometimes, it doesn’t matter how clever a system is, or how secure it is, or if you have a user’s manual, access to the distributor or even special keys. All you need is some common sense and a hack. In this instance, the 5-digit key code is placed in its full glory on the actual RAP module, where you can see the number in front of your face. Another option is using a special programmer device that links up to the OEM through the ODBII, not all of them give you the 5-digit feature, but some have been tweaked to do so.

    More Ford Reviews – See our best:

    • F150 Leveling Kit
    • Tuners for 5.0 F150
    • Tuners for F150 Ecoboost
    • Tonneau Cover for F-150
    • Cam Heads for 351W Ford
    • Cam for 302 Ford Truck
    • Lift Kits for F250 Super Duty
    • Replacement Shocks for Ford Ranger
    • Shocks for Ford F350